Enerpac VM43 Instrukcja Użytkownika Pobierz pdf (Strona 1)

POWERFUL SOLUTIONS. GLOBAL FORCE.

Instruction Sheet

VM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43L

MANUALLY OPERATED CONTROL VALVES

L1057 Rev. C 08/12

1.0 IMPORTANT RECEIVING INSTRUCTIONS

Visually inspect all components for shipping damage. Shipping

damage is not covered by warranty. If shipping damage is found,

notify carrier at once. The carrier is responsible for all repair and

replacement costs resulting from damage in shipment.

SAFETY FIRST

2.0 SAFETY ISSUES

Read all instructions, warnings and cautions

carefully. Follow all safety precautions to avoid

personal injury or property damage during system

operation. Enerpac cannot be responsible for damage or injury

resulting from unsafe product use, lack of maintenance or

incorrect product and/or system operation. Contact Enerpac

when in doubt as to the safety precautions and operations. If you

have never been trained on high-pressure hydraulic safety,

consult your distribution or service center for a free Enerpac

Hydraulic safety course.

Failure to comply with the following cautions and warnings could

cause equipment damage and personal injury.

A CAUTION is used to indicate correct operating or maintenance

procedures and practices to prevent damage to, or destruction of

equipment or other property.

A WARNING indicates a potential danger that requires correct

procedures or practices to avoid personal injury.

A DANGER is only used when your action or lack of action may

cause serious injury or even death.

WARNING: Wear proper personal protective gear when

operating hydraulic equipment.

WARNING: Stay clear of loads supported by

hydraulics. A cylinder, when used as a load lifting

device, should never be used as a load holding device.

After the load has been raised or lowered, it must always be

blocked mechanically.

WARNING: USE ONLY RIGID PIECES TO HOLD

LOADS. Carefully select steel or wood blocks that are

capable of supporting the load. Never use a hydraulic

cylinder as a shim or spacer in any lifting or pressing application.

DANGER: To avoid personal injury keep hands

and feet away from cylinder and workpiece during

operation.

WARNING: Do not exceed equipment ratings. Never

attempt to lift a load weighing more than the capacity of

the cylinder. Overloading causes equipment failure and

possible personal injury. The cylinders are designed for a max.

pressure of 700 bar [10,000 psi]. Do not connect a jack or

cylinder to a pump with a higher pressure rating.

Never set the relief valve to a higher pressure than the

maximum rated pressure of the pump. Higher settings

may result in equipment damage and/or personal injury.

WARNING: The system operating pressure must not

exceed the pressure rating of the lowest rated

component in the system. Install pressure gauges in the

system to monitor operating pressure. It is your window to what

is happening in the system.

CAUTION: Avoid damaging hydraulic hose. Avoid sharp

bends and kinks when routing hydraulic hoses. Using a

bent or kinked hose will cause severe back-pressure.

Sharp bends and kinks will internally damage the hose leading

to premature hose failure.

Do not drop heavy objects on hose. A sharp impact

may cause internal damage to hose wire strands.

Applying pressure to a damaged hose may cause it to

rupture.

IMPORTANT: Do not lift hydraulic equipment by the

hoses or swivel couplers. Use the carrying handle or

other means of safe transport.

CAUTION: Keep hydraulic equipment away from

flames and heat. Excessive heat will soften packings

and seals, resulting in fluid leaks. Heat also weakens

hose materials and packings. For optimum performance do not

expose equipment to temperatures of 65°C [150°F] or higher.

Protect hoses and cylinders from weld spatter.

DANGER: Do not handle pressurized hoses.

Escaping oil under pressure can penetrate the skin,

causing serious injury. If oil is injected under the skin,

see a doctor immediately.

MAKE SURE ALL HYDRAULIC CONNECTIONS

ARE MADE TO THE PROPER PORTS.

Index:

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-20

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-25

Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-30

Portuguese . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-35

Swedish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-40

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41-45

Loctite 222

Rounded Edge Down

Bord arrondi vers le bas

Runde Kante unten

Bordo arrotondato

verso il basso

Borde redondeado

hacia abajo

Afgeronde kant omlaag

Lateral arredondada

para baixo.

Rundad kant nedåt

Repair Parts Sheets for this product are available from the

Enerpac web site at www.enerpac.com, or from your nearest

Authorized Enerpac Service Center or Enerpac Sales office.

www.enerpac.com

Handtagsenhet

1 2 3 4 5 6 ... 47 48

Podsumowanie treści

Strona 1 - Instruction Sheet

POWERFUL SOLUTIONS. GLOBAL FORCE.Instruction SheetVM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43LMANUALLY OPERATED CONTROL VALVESL1057 Rev. C 08/121.0

Strona 2 - 5.0 OPERATION

SCHÉMAS DE DISTRIBUTEURS 4 VOIES MANUELSDistributeurs du type manuel Distributeurs du type manuel verrouillableAvance-Neutre/Maintien-Rentrer Avance-N

Strona 3 - 9.0 STORAGE INSTRUCTIONS

www.enerpac.com11BedienungsanleitungVM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43LMANUELL BETÄTIGTE REGELVENTILEL1057 Rev. C 08/121.0 WICHTIGE VERFAH

Strona 4 - 3-WAY MANUAL VALVE DIAGRAMS

Komponenten einen Sprungvollausfall erleiden, was schwereVerletzungen hervorrufen kann.WARNUNG: Sicherstellen, dass die anlage stabilisiert,bevor eine

Strona 5 - 4-WAY MANUAL VALVE DIAGRAMS

5.1 Einstellung des Überdruckventils (ModelleVM33/33L/43/43L)Pumpen der Z-Klasse sind mit einem vom Benutzer einstellbarenÜberdruckventil ausgestatte

Strona 6 - Fiche dʼinstructions

HYDRAULIKSCHALTPLÄNE DES 3-STELLUNGS-WEGEVENTILSManuelle Ventile Manuell gesperrte VentileAusfahren-Neutral/Halt-Zurückziehen Ausfahren-Neutral/Halt-Z

Strona 7 - 5.0 FONCTIONNEMENT

Manuelles 4-Stellungs-Wegeventil VC-4 Manuell betätigtesVorsteuerventil: Mit Hilfeder Tippschaltungkönnen in der Mittelstellung die Zylinderhydraulisc

Strona 8

Foglio IstruzioniVALVOLE A COMANDO MANUALE VM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43L161.0 NOTA IMPORTANTEIspezionare visivamente tutti i compone

Strona 9

AVVERTENZA: Utilizzare i cilindri idraulici solo se igiunti del sistema sono debitamente accoppiati. Se ilsovraccarico del cilindro diventa eccessivo,

Strona 10 - Monté sur pompe

5.1 Regolazione della valvola di scarico (ModelliVM33/33L/43/43L)Le pompe della classe Z sono equipaggiate con una valvola discarico regolabile da par

Strona 11 - SICHERHEIT GEHT VOR

DIAGRAMMA CARATTERISTICA VALVOLE MANUALI A 3 VIEValvole manuali Manual Locking ValvesAvanzamento-Neutro/Chiusura-Rientro Avanzamento-Chiuisura-Rientro

Strona 12 - 5.0 BETRIEB

2WARNING: Only use hydraulic cylinders in a coupledsystem. Never use a cylinder with unconnected couplers.If the cylinder becomes extremely overloaded

Strona 13 - Einstellschraube

PT"GP""GP"TAB"GA""GB"DIAGRAMMA CARATTERISTICA VALVOLE MANUALI A 4 VIEValvole di tipo manuale Valvole di blocca

Strona 14 - Rohrleitungsmontage

211.0 IMPORTANTES INSTRUCCIONES DE RECEPCIÓNInspeccione visualmente todos los componentes para verificar sihay daños de envío. Debido a que la garant

Strona 15 - Montage an der Pumpe

ADVERTENCIA: Asegurese que el equipo sea antes delevantar la carga. El cilindro debe colocarse sobre unasuperficie plana capaz de soportar la carga. D

Strona 16 - VALVOLE A COMANDO MANUALE

23NOTA: Para lograr un ajuste preciso, disminuir la presiónhasta un valor inferior al de ajuste final y a continuaciónaumentar la presión hasta alcanz

Strona 17 - 5.0 FUNZIONAMENTO

DIAGRAMAS DE VÁLVULAS MANUALES DE 3-VÍASVálvulas Manuales Válvulas de retención manualAvanzar-Neutro/Sostener-Retraer Avanzar-Sostener-RetraerVálvula

Strona 18 - Regolare la vite

Válvula direccional de4-vías manual VC-4Válvulas remotasaccionadasmanualmente. Permite elcontrol con los dedos para el avancey la retracción con acci

Strona 19 - Attacco sulla pompa

261.0 BELANGRIJKE INSTRUCTIES BIJ ONTVANGSTControleer visueel alle onderdelen op schade opgelopen tijdens deverzending. Schade opgelopen tijdens de v

Strona 20

WAARSCHUWING: Gebruik hydraulische cilinders enkelin een aangesloten systeem. Nooit een cilinder gebruikenmet koppelingen die niet aangesloten zijn. A

Strona 21 - Hoja de Instrucciones

1. Installeer een meter op de pomp. Als een apparaat uitgerustis met een optionele druktransductor, moet wordengeverifieerd dat de "DRUK INSTELLE

Strona 22

3-WEG KLEPPEN SCHEMA'SHandmatig bediende kleppen Handmatig bediende blokkeerkleppenVerplaatsen-Neutraal/Houden-Intrekken Verplaatsen-Houden-Intre

Strona 23 - 8.0 SISTEMA HIDRÁULICO

3Figure 26.0 TROUBLE SHOOTING1. System will not build pressure. Check relief valve in thecontrol valve or in the pump, for proper setting (see pumpre

Strona 24 - Montaje por Bomba

Op afstand gemonteerd MountedVC-4 Handmatigbediende 4-wegrichtklep -Handmatig, op afstandbediende klep. Metvingertipbediening voorhet verplaatsen en i

Strona 25 - Avanzar-Sostener-Retraer

31Folha de instruçãoVÁLVULAS DE CONTROLE COM ACIONAMENTO MANUALVM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43LL1057 Rev. C 08/121.0 INSTRUÇÕES IMPORTAN

Strona 26 - HANDBEDIENDE REGELKLEPPEN

AVISO: CERTIFIQUE-SE QUE A INSTALAÇÃO SEJAESTÁVEL ANTES DE LEVANTAR A CARGA. Oscilindros deverão ser posicionados em uma superfícieplana para suporta

Strona 27 - 5.0 WERKING

332. Acione a bomba para permitir o aquecimento do óleo.3. Solte a porca trava do parafuso de ajuste.4. Mude a posição da válvula e coloque pressão no

Strona 28 - 9.0 OPSLAGINSTRUCTIES

DIAGRAMA DA VÁLVULA DE 3-VIAS MANUAL Válvulas manuais Válvulas de travamento manualAvançar Neutro/Espera-retrair Avançar-esperar-retrairVálvulas de 3-

Strona 29 - 3-WEG KLEPPEN SCHEMA'S

Montagem remotaVálvula direcional de4-vias VC-4 manual –Válvula remotaoperada manualmente.Permite controle digitalpara avanço e retração doscilindros

Strona 30 - 4-WEG KLEPPEN SCHEMA'S

InstruktionsbladVM/VC-3/3L/4/4L/15/15L/20/20L, VM33/33L/43/43LMANUELLT STYRDA RIKTNINGSVENTILER361.0 VIKTIGA MOTTAGNINGSINSTRUKTIONERKontrollera att i

Strona 31 - Folha de instrução

VARNING! SÄKERSTÄLL ATT UPPSTÄLLNINGEN ÄRSTABIL INNAN DU LYFTER LAST. Cylindrar skallplaceras på en plan yta som kan bära lasten. Använd encylinderbas

Strona 32

7. Kontrollera det slutliga trycket igen genom att slå om ventilenoch trycksätta systemet.Figur 26.0 FELSÖKNING1. Systemet bygger inte upp tryck. Kon

Strona 33 - 7.0 MANUTENÇÃO

39VC-3 manuell 3-vägsriktningsventil –Montera denna på någon behändigplats i systemet där du behöver enkontrollpunkt.VC-15 manuell 3-vägsriktningsvent

Strona 34 - Bomba fixada

VC-3 Manual 3-Way Directional Valve –Mounts at any convenient locationin system where control point isneeded.VC-15 Manual 3-WayDirectional Valve –Clos

Strona 35

40FjärrmonteradVC-4 manuell 4-vägsriktningsventil –Manuellt fjärrstyrd ventil.Ger digfingertoppskontroll avkraftframföring och -tillbakadragning avcyl

Strona 36 - 2.0 SÄKERHETSFRÅGOR

41L1057 Rev. C 08/12 www.enerpac.com

Strona 37

3 - In Use132AB42

Strona 38 - 9.0 FÖRVARINGSINSTRUKTIONER

AB43

Strona 39 - Fjärrmonterad

APTAPTAPTAPTAPTAPTVM33VM33LPTA"GA""GP""GP"TPTA"GP""GP""GA"T44

Strona 40

4APTBPTA BPTABAPTBAPTBPTA BVM43VM43PTAB"GA""GB""GP""GP"TPT"GP""GP"TAB"GA""G

Strona 41

Strona 42

Strona 43

Australia and New ZealandActuant Australia Ltd. Block V Unit 3Regents Park Estate391 Park RoadRegents Park NSW 2143(P.O. Box 261) AustraliaT +61 (0)2

Strona 44

5Remote MountedVC-4 Manual 4-WayDirectional Valve –Manually operated remotevalve. Allows finger tipcontrol for powered advanceand retraction of cylind

Strona 45

61.0 INSTRUCTIONS IMPORTANTES RELATIVES À LA RÉCEPTION Inspecter tous les composants pour vous assurer qu’ils n’ont subiaucun dommage en cours d’expé

Strona 46

En cas d’injection d’huile sous la peau, contacter immédiatementun médecin.AVERTISSEMENT : Utiliser des vérins hydrauliquesuniquement dans un système

Strona 47

5.1 Réglage de la soupape de retour (modèlesVM33/33L/43/43L)Les pompes de classe Z sont dotées d’une soupape de retourréglable par l’utilisateur (voi

Strona 48

SCHÉMAS DE DISTRIBUTEURS 3 VOIES MANUELSDistributeurs manuels Distributeur à verrouillage manuelAvance-Neutre/Maintien-Rentrer Avance-Maintien-Rentrer